Booster Fan Duct Booster Fan
Date of issue:2022/12/3 10:48:52 Number of Views:
Booster Fan Duct Booster Fan:
Booster fan duct booster fan,they are generally used in forging furnaces and high-pressure forced ventilation. The gas does not contain viscous substances, the dust and hard particles contained do not exceed 150mg/m3, and the gas temperature is 20-800 °C.
Booster fan duct booster fan can be made into two types: right-handed and left-handed. From the side of the motor, if the impeller rotates clockwise, it is called a right-handed fan, denoted by "right"; the impeller rotating counterclockwise is called a left-handed fan, denoted by "left".
The position of the air outlet of the fan, expressed by the angle of the air outlet of the casing. "Left" and "Right" can be made into six angles of 0°, 45°, 90°, 135°, 180°, and 225°.
Before installation: All parts of the fan should be checked comprehensively, whether the parts are complete, whether the rotation direction of the impeller and the casing are consistent, and whether the connection of each part is tight. Whether the impeller, main shaft, bearing and other main parts are damaged, whether the transmission group is flexible, etc.
When installing: pay attention to check the casing, and there should be no tools and debris left in the casing. In order to prevent rust and reduce the difficulty of disassembly on some joint surfaces, some grease or mechanical oil should be coated. The connection surface between the fan and the foundation, the inlet and outlet ducts should be adjusted to match naturally, and the connection should not be forced, and it is not allowed to add the weight of the duct to each part of the fan. And pay attention to ensure the horizontal position of the fan.
Booster fan duct booster fan installation requirements:
(1) Install according to the position and size shown in the drawing. In order to ensure high efficiency, ensure the axial and radial clearance between the air inlet and the impeller.
(2) After installation, try dialing the transmission group to check whether it is too tight or collides with the fixed part.
(3) After all installations are completed and the general inspection is passed, the test operation of the fan can be carried out.
In order to prevent the motor from being overloaded and burned, when the fan starts, it must be carried out under no load (close the air inlet valve and open the air outlet valve slightly). If the condition is good, gradually open the valve until the specified working condition. During operation, the current should be strictly controlled and the rated value should not be exceeded.
Booster Fan Duct Booster Fan:
Booster fan duct booster fan,they are generally used in forging furnaces and high-pressure forced ventilation. The gas does not contain viscous substances, the dust and hard particles contained do not exceed 150mg/m3, and the gas temperature is 20-800 °C.
Booster fan duct booster fan can be made into two types: right-handed and left-handed. From the side of the motor, if the impeller rotates clockwise, it is called a right-handed fan, denoted by "right"; the impeller rotating counterclockwise is called a left-handed fan, denoted by "left".
The position of the air outlet of the fan, expressed by the angle of the air outlet of the casing. "Left" and "Right" can be made into six angles of 0°, 45°, 90°, 135°, 180°, and 225°.
Before installation: All parts of the fan should be checked comprehensively, whether the parts are complete, whether the rotation direction of the impeller and the casing are consistent, and whether the connection of each part is tight. Whether the impeller, main shaft, bearing and other main parts are damaged, whether the transmission group is flexible, etc.
When installing: pay attention to check the casing, and there should be no tools and debris left in the casing. In order to prevent rust and reduce the difficulty of disassembly on some joint surfaces, some grease or mechanical oil should be coated. The connection surface between the fan and the foundation, the inlet and outlet ducts should be adjusted to match naturally, and the connection should not be forced, and it is not allowed to add the weight of the duct to each part of the fan. And pay attention to ensure the horizontal position of the fan.
Booster fan duct booster fan installation requirements:
(1) Install according to the position and size shown in the drawing. In order to ensure high efficiency, ensure the axial and radial clearance between the air inlet and the impeller.
(2) After installation, try dialing the transmission group to check whether it is too tight or collides with the fixed part.
(3) After all installations are completed and the general inspection is passed, the test operation of the fan can be carried out.
In order to prevent the motor from being overloaded and burned, when the fan starts, it must be carried out under no load (close the air inlet valve and open the air outlet valve slightly). If the condition is good, gradually open the valve until the specified working condition. During operation, the current should be strictly controlled and the rated value should not be exceeded.
- Previous:Workshop Roof Ventilator
- Next:没有了!